Converts the Ducati specific underseat battery charge connector (found on recent models) to an industry standard SAE 2-pole connector.

 

• Length=12″/30cm
• Ducati >2010 connector,
• Industry standard 2-pin SAE connector
• 15A fuse
• Cable max. rating: 5 Amp
• -40°C/-40°F very low temperature use; cable remains flexible at ‘below freezing’ temperatures.

 Includes sealing cap for OptiMATE heavy duty SAE connector.

Premium cable designed by TecMate

SPECIFICATIONS BC DUETTO:

• Input voltage 220 ÷ 240Vac, 50 ÷ 60 Hz
• Output voltage 13.8 V / 14.4 V - 12 V Nominal
• Charging current 1.5 A max
• Battery types 12 V lead-acid (wet batteries, gel, maintenance-free, VRLA, AGM, Ca / Ca, etc) & 12V LiFePO4
• Charging algorithm - lead-acid 8 automatic charging (Initialization, Recovery,
• Soft Charge, Bulk Charge, desulfation,
• Battery Analysis, Maintenance and Equalization)
• Battery capacity - Lead Acid From 3 Ah to 70 Ah (charging), up to 100 Ah (Maintenance)
• Charging algorithm - LiFePO4 7 automatic charge levels
• (Initialization, Recovery, Soft Charge, Bulk Charge, Compensation, Battery Analysis, conservation)
• Battery capacity - LiFePO4 From 1 Ah to 100 Ah
• Operating temperature from -20 ° to + 50 ° C
• IP protection
• Weather resistant - splash protection IP44
• Suitable for outdoor use

BC DUETTO is the intelligent universal charger for both lead-acid and lithium batteries, which was developed to provide a single multipurpose device for all 12V motorcycle batteries. The charger has two different charging programs for lead-acid and LiFePO4 batteries. Its maximum charging current of 1.5 amperes makes it ideal not only for rest, charge and maintain all atv, moped and motorcycle batteries, but also for maintenance of car batteries.
The charger can always stay connected to the battery, with no risk and no need to disconnect the battery from the vehicle: it is during periods of inactivity keep getting charged (even months) the battery.
The internal microprocessor performs a fully automated multi-cycle charging algorithm (8 cycles for lead-acid batteries, 7 cycles for LiFePO4 batteries ). The charging technology for lead acid batteries is ideal (from 1.25 volts) charging deeply discharged batteries and for charging, desulfate and maintain all 12V batteries (maintenance free sealed, with caps, gel ...) 3 to 70 Ah (up to 100 Ah for Maintenance only). The LiFePO4 program allows you to restore deeply discharged batteries, a fast and efficient charging of the battery, a charge balance between the battery cells and the proper maintenance of the battery during long periods. The safety is ensured at every stage of charge: at low
temperatures, which are recognized by an integrated sensor which is the POLAR mode activated specifically for safe charging at low ambient temperature.
A few LEDs indicate the charging cycle executed as well as any error messages in real time .
BC DUETTO not produce sparks and is protected against short circuit, reverse polarity, overcharging and overheating. The package includes a waterproof battery cable with eyelets (code STD2V), which can always be mounted on the vehicle, and a battery cable with insulated clamps (code 30AMPPZ). A 12/18 mm universal adapter (code ACC612V - optional) is available to recharge the battery from the cigarette lighter. The warranty is extended to 3 years.

Package Contents:
- the battery charger BC DUETTO, with the battery connection cable (2 meters long);
- a battery cable with eyelets STD2V that can remain permanently installed on board;
- a battery cable with alligator clips 30AMPPZ;
- according to the selected kit, a battery connection cable for cigarette lighter socket (12/18 mm) ACC612V be included;
- a copy of the user manual.

NOW with matching DDA plug, original Ducati 51040111A  EURO 4 Model
UP 2020 / EURO 5 Model need a extra Cable ( See Product recommendation )

Ducati Lithium ION Battery Charger and 12,8 V LiFePO4
for Ducati battery 96580071A or other Lithium Battery

 for example from the 1299 Panigale
incl . universal adapter for all Europe power sockets, USA / Japan and Australia / Japan

• Voltage: 220-240 VAC, 50-60 Hz
• Charging voltage: 14.4 V; nominally 12 V
• Reverse current: <1 mA
• Charging current: max. 0.8 A
• Charger Type: High-frequency charger with three-stage, fully automatic charging cycle IUoUp without spikes
• Battery capacity: 1.2 Ah to 32 Ah
• Dimensions: 142x51x36 mm (LxWxH)
• IP 65
• Weight: 0.3 kg
• Battery types: open, maintenance-free, AGM, GEL, and lead-calcium

JMP Skan Monitor 2
Battery monitoring with the smartphone

With the JMP Skan Monitor 2 and the new and free Apple or Android app "JMP BatteryMonitor II" you are able to

Check the battery charge level quickly and easily. Only with a constant,

full battery capacity and usability is guaranteed.

The positive state of charge also prevents possible early damage or battery failure.

The continuous recording records the charge status of the battery while driving and can also be called up later.

The file with the data can be sent by email from the smartphone and displayed in Excel.

So you can quickly see where the charging voltage has dropped or was too high. A defective controller can be recognized quickly.

In addition, the new app can also be used to precisely check starting processes (starters, cable connections, etc.) and charging processes (alternator, cables, etc.).

This saves long troubleshooting in the event of a problem. If the battery is low or there are other problems, a notification can warn the driver, depending on the setting in the app options.

After simply connecting it to the battery using eyelets and downloading the new Android or Apple app, the current voltage value can be called up.

The transmitter can be used for 12 V batteries.
The range is about 10 meters.
The connection is made via Bluetooth. (Only from Bluetooth 4.0; e.g. from iPhone 4s, iPad3 or iPod Touch 5)

The JMP Skan Monitor 2 is ideal for detecting overvoltage> 14.9 V of the alternator before it damages the battery.

Please note: The new JMP BatteryMonitor II app is required for the new JMP Skan Monitor 2!

If the minimum voltage is undershot, the battery should be recharged soon.
- Easy attachment to the battery using eyelets
- Power consumption only about 2 mA
- Reverse polarity does not damage the transmitter or the battery
- Download the free app from the Apple App Store or the Google Play Store under JMP Battery Monitor II
- Voltage recording even while driving. Result can be sent via email. The file can be viewed in Excel.

Lithium-ion batteries by JMT, tech for your motorcycle.
By replacing a standard lead-acid battery with a lithium-ion battery JMT up to 5 kg are saved without significant

Following advantages speak for JMT lithium-ion batteries:

- About 1/3 of the weight of lead-acid battery similar
- Unbeatable ratio of cost / weight reduction
- Operates in any position, as they contain no acid
- Contains no heavy metals
- Balanced discharge / charge of all cells by Balancer
- Fast charging with high charge (up to 90% in 6 min)
- Very low self-discharge (up to 5% per month)
IMPORTANT: micro consumers, such as Navihalter etc. ALWAYS put on ignition plus!
- Even at high temperatures still good performance 60-80 ° C.
- Safe technology and long life

Lead-acid batteries can be due to the specific properties use only 30% of its capacity, while lithium-ion batteries, nearly 100% of the capacity can be used.
For this reason, the lithium batteries JMT versions for the same starting power require only 1/3 of the capacity of a comparable lead-acid battery.
A uniform charge of all cells is also ensured by a built-in processor ("balancer").
The dimensions of the lithium-ion batteries by using adapters correspond to the dimensions of the original lead-acid batteries.
The connections are the same, so the battery can be replaced without further adjustments in a few minutes.

JMT lithium-ion batteries can be controlled with conventional chargers (eg JMP JMP 800 or 4000 or Optimate Lithium ) are charged.
The normal charging current is generally equal to about the capacity (eg 2.8 Ah = 2.8 A charge current).
In a quick-charge, even a charging current can be used, which corresponds to a maximum of 10 times the capacity (for example, 2.8 Ah = 28A charging current).
We recommend the use of JMP30000Pro charger and compliance with the technical. Data values ​​mentioned.

Although the lightweight battery is real living, it should be noted that the starting capacity is given at temperatures below zero degrees Celsius limited.

12V/4,8Ah
Comparable with the dimensions and connections with:
 Yuasa YT12B-BS YT14B-BS YB16AL-A2

 -12 V maintenance-free lithium-ion battery

-Energy 58.0 WH

-Dimensions in mm 150 x 65 x 130

-Charging current recommended 2.5 amps

-maximum charge current for fast charging 24 amps

-Weight under 1.0 kg

-Low-temperature test current 290

12V/4,8Ah  Fit for :

Scrambler

Ducati S 620-800ie

Multistrada 620-1100

Multistrada 1200

Monster S2R - S4R(S)

Monster 696-1100( EVO )

Monster 400-1000

Hypermotard 796-1100( EVO )

Desmosedici RR

Diavel

Ducati 851-888

Ducati 748-998

Ducati 749-999

Ducati SS und SL  all Modell and Years

Ducati Streetfighter

ST2- ST4 ( ABS ) und ST3 ( ABS )

All Sport and Classic Modelle 750-1000 / GT 1000

fits for:

QA55V / CCH299

DUCATI
B Supermono 550 1993

B 748R 748 2000

B 851 SP4 888 1992 1993
B 888 (SPS-SP5) 888 1992 1993
B Superbike 851 (SP2) 888
B Superbike 851 (SP3) 888
B 916 SP2 916 1995 1996
B 916 SP3 916 1996 1997
B 916 Sport Production (SP) 916 1994 1995
B Racing 950 1995
B 916 SPS Race 996 1997 1999

For easy loading without removing the battery.

Please check with your model, whether comparative battery + and - is the plug.

zb. Multistrada 1200, Monster 1100, Hypermotard 1100

Pins:

1) +12V

2) Ground

3) ECU B1 pin / CAN Hi

4) ECU C1 pin / CAN Lo

one piece incl. Pins

The original DDA Plug looks so:

Lithium-ion batteries of JMT, high-tech for your motorcycle.

The latest generation batteries recognizable by the red cover.

Ducati Monster 937, 
Ducati Panigale 899, 955 V2, 959, 1199, 1299, 1000 V4, 
Ducati Streetfighter 955 V2, 1100 V4,  
Ducati Supersport 950, 

Spacer (S)
Battery is equipped with one or more spacers which are taped with adhesive strip under the battery so that the battery fits exactly into the battery box.

Indicator (I)
All batteries are equipped with a battery state - equipped Indicator.
Simply press the test button. Lights every 3 blue LEDs on the battery fully (ful) is loaded. Lights only 2 LEDs, it is charged only half (med). At the latest when only one LED (low), the battery must be charged.

By replacing a standard lead-acid battery with a lithium-ion battery JMT up to 5 kg in weight can be saved, without any appreciable effort.

Following advantages speak for JMT lithium-ion batteries:
- Approximately 1/3 of the weight of comparable lead-acid battery
- Unbeatable ratio of cost / weight saving
- Because in each position can be installed no acid
- Does not contain heavy metals
- Balanced discharge / charge of all cells by Balancer
- Fast charging with high charging current (up to 90% in 6 min)
- Very low self-discharge (max. 5% per month)
IMPORTANT: micro consumers, such as Navihalter etc. ALWAYS put on ignition plus!
- Even at high temperatures still good performance up to 60 ° C
- Safe technology and high durability

Lead-acid batteries can be used only 30% of their capacity due to the specific properties,
while nearly 100% of the capacity can be used in lithium ion batteries.

For this reason, lithium batteries JMT versions of the same starting power need only 1/3 of the capacity of a comparable lead-acid battery.
A steady state of charge of all cells is also ensured by a built-in processor ("balancer").
The dimensions of lithium-ion batteries using adapters correspond to the dimensions of the original lead-acid batteries.
The ports are the same, so the battery can be replaced without additional adjustments in a few minutes.

Please note that the shop only suitable chargers may be used. We recommend JMP chargers.
The maximum recommended load currents, refer to Technical Data below

Under no circumstances chargers may be used that attempt to desulfate deeply discharged batteries with 10 volts with a voltage of more than 14.9 volts, before they begin the actual charge.
The maximum charging voltage of 14.9 volts may be exceeded under any circumstances. Risk of explosion.

The manufacturer guarantees a sufficient initial capacity of up to -5 degrees Celsius.

Technology
JMT use lithium-ion batteries as a cathode material iron phosphate (LiFePO4) and lithium-polymer using the method of manufacture.
This allows them to rise even explode either in flames during normal operation.
The technology and the manufacturing process ensure the highest safety standards for lithium batteries.

- 12 V maintenance-free lithium-ion battery
- Recommended charging current 1.5A
- Maximum charge current for fast charging 15 A

Comparable in dimensions and connections with:
Yuasa Manufacturer number
YT7B-BS
YT9B-BS

12V/3,0Ah
- 12 V wartungsfreie Lithium-Ionen-Batterie
- Energie 36,0 Wh : 3,0 Ah
- Maße in mm 150x65x92,99,106
- Ladestrom empfohlen 1,5 Ampere
- maximaler Ladestrom für Schnellladung 15 Ampere
- Gewicht ca. 0,6 kg
- Kälteprüfstrom 180